Network Reset Instructions
To reset the controller network settings to the default:
- Disconnect power to the controller.
- While pressing and holding the ID button on the back of the controller, power on the controller.
- Hold the ID button until the ID button turns solid orange and the Link and Power LEDs are solid blue, and then immediately release the button.
Note: During the reset process, the ID button provides the same feedback as the Caution LED on the front of the controller.
Factory Restore Instructions
To restore the controller to the factory default image:
- Insert one end of a paper clip into the small hole on the back of the controller labeled RESET.
- Press and hold the RESET button. The controller resets and the ID button changes to solid red.
- Hold the button until the ID flashes double orange. This should take five to seven seconds. The ID button flashes orange while the factory restore is running. When complete, the ID button turns off and the device power cycles one more time to complete the factory restore process.
Instrucciones para el restablecimiento de la red
Para restablecer la configuraci贸n de red del controlador a los valores predeterminados:
- Desconectar la alimentaci贸n del controlador.
- Mientras mantienes pulsado el bot贸n ID de la parte posterior del controlador, enciende el controlador.
- Mant茅n pulsado el bot贸n ID hasta que el bot贸n ID se vuelva naranja s贸lido y los LEDs de Link y alimentaci贸n se vuelvan azules s贸lidos. Suelta inmediatamente el bot贸n.
Nota: Durante el proceso de reinicio, el bot贸n ID proporciona la misma informaci贸n que el LED de precauci贸n de la parte frontal del controlador.
Instrucciones para el restablecimiento de los valores de f谩brica
Para restablecer la imagen de f谩brica del controlador:
- Inserta un extremo de un clip en el peque帽o orificio de la parte posterior del controlador etiquetado como RESET.
- Mant茅n pulsado el bot贸n RESET. El controlador se reiniciar谩 y el bot贸n ID cambia a rojo s贸lido.
- Mant茅n el bot贸n pulsado hasta que el ID parpadee en naranja dos veces. Esto deber铆a llevar de cinco a siete segundos. El bot贸n ID parpadea en naranja mientras se ejecuta la restauraci贸n de f谩brica. Cuando se completa, el bot贸n ID se apaga y el dispositivo se enciende una vez m谩s para completar el proceso de restauraci贸n de f谩brica.
Istruzioni per il ripristino della rete
Per ripristinare le impostazioni di rete del controllore:
- Scollegare l'alimentazione del controller.
- Tenendo premuto il pulsante ID sul retro del controller, accendere il controller.
- enere premuto il pulsante ID finch茅 non diventa arancione fisso e i LED Link e Power sono blu fissi, quindi rilasciare immediatamente il pulsante.
Nota: durante il processo di reset, il pulsante ID fornisce lo stesso feedback del LED di attenzione sulla parte anteriore del controller.
Istruzioni per il ripristino delle impostazioni di fabbrica
Per ripristinare l'immagine di fabbrica del controllore:
- Inserire un'estremit脿 di una graffetta nel piccolo foro sul retro del controller contrassegnato da RESET.
- Tenere premuto il pulsante RESET. Il controller si ripristina e il pulsante ID diventa rosso fisso.
- Tenere premuto il pulsante finch茅 l'ID non lampeggia in doppio arancione. Dovrebbero essere necessari da cinque a sette secondi. Il pulsante ID lampeggia in arancione mentre 猫 in corso il ripristino di fabbrica. Al termine, il pulsante ID si spegne e il dispositivo si riaccende un'altra volta per completare il processo di ripristino di fabbrica.
Instructions de r茅initialisation du r茅seau
Pour r茅initialiser les param猫tres r茅seau du contr么leur aux valeurs par d茅faut:
- D茅branchez l'alimentation du contr么leur.
- Tout en maintenant enfonc茅 le bouton ID 脿 l'arri猫re du contr么leur, mettez le contr么leur sous tension.
- Maintenir le bouton ID jusqu'脿 ce qu'il devienne orange fixe et que les voyants Link et Power soient bleus fixes, puis rel芒cher imm茅diatement le bouton.
Remarque: Pendant le processus de r茅initialisation, le bouton ID fournit le m锚me retour d'information que la LED d'avertissement situ茅e 脿 l'avant du contr么leur.
Pour restaurer l'image par d茅faut du contr么leur
To restore the controller to the factory default image:
- Ins茅rer une extr茅mit茅 d'un trombone dans le petit trou situ茅 脿 l'arri猫re du contr么leur et intitul茅 RESET.
- Appuyer sur le bouton RESET et le maintenir enfonc茅. Le contr么leur se r茅initialise et le bouton ID devient rouge fixe.
- Maintenez le bouton enfonc茅 jusqu'脿 ce que le bouton ID clignote en double orange. Cela devrait prendre cinq 脿 sept secondes. Le bouton ID clignote en orange pendant que la restauration d'usine est en cours. Une fois la restauration termin茅e, le bouton ID s'茅teint et l'appareil effectue un nouveau cycle d'alimentation pour terminer le processus de restauration d'usine.
No comments:
Post a Comment